As an Amazon Associate we earn from qualifying purchases. Affiliate disclosure

ECI Power 100W 12V Solar Kit with 20Ah LiFePO4 Battery Review: Specs, Pros and Cons

Latest update:

As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.

ECI Power's CLBE1220L100C6 is a small complete 12V solar system: one 100W monocrystalline rigid panel, a 12V 20Ah LiFePO4 battery, a 10A PWM charge controller, a pair of 10 ft 12AWG MC4 cables, 6 ft 12AWG battery cables and panel mounting brackets. ECI rates the battery for at least 2,000 cycles at 80% depth of discharge, and up to 5,000 at 50%. The controller detects 12V or 24V systems, adjusts charging for temperature and has a display for state of charge and battery health. It suits a shed light, a trolling-motor top-up or a small camper load, not a fridge running all night. Our review draws on ECI Power's published kit list and specs.

What stands out

  • 100W mono rigid panel, 40.2 x 20.1 in
  • 12V 20Ah LiFePO4 battery, 2,000 cycles at 80% DOD
  • 10A PWM controller with display, 12/24V detect
  • 10 ft MC4 and 6 ft battery cables, 12AWG
  • Mounting brackets included

Who it fits

Good fit for

First-time solar buyers who want a matched 12V kit for a shed, chicken coop, small boat or pop-up camper, with the battery already included.

Who should skip it

RVers with a fridge or inverter loads (20Ah runs out fast), and anyone who wants MPPT efficiency or room to add more panels on the same controller.

Verdict: A tidy, fully matched starter kit; size up if your loads run overnight.

ECI Power kit parts explained

100W mono panel

Typical output in good sun is well below 100W; plan around a few hundred Wh per day at most.

12V 20Ah LiFePO4

A small battery for lights, fans, USB loads and a pump.

2,000 cycles at 80% DOD

ECI's minimum rating; up to 5,000 cycles at 50%.

10A PWM controller

Fine for one 100W panel; PWM leaves more on the table than MPPT.

12AWG cables, 10 ft and 6 ft

Heavy enough gauge for this current over these runs.

What is in the ECI Power box

Everything needed to wire a basic system arrives together: panel, battery, controller, MC4 extension pair, battery leads and Z-style mounting brackets. The controller's screen shows charge state and battery health and is set up for LiFePO4 with a CC-CV charge profile. The listing does not give the panel's Voc or the battery's weight or size, which matters if space on a boat or trailer is tight.

Running a small 12V setup

Mount the panel on a shed roof or trailer tongue box, wire it to the controller, then the controller to the battery, and run 12V lights, a vent fan or a phone charger from it. A 12V 20Ah battery covers an evening of LED lighting and device charging with ease; a 12V compressor fridge would drain it in well under a day, so the kit fits light loads. There is no inverter in the box, so AC devices need one bought separately.

Before buying the ECI Power 100W kit

Match it to your loads.

Check before you buy

  • Your daily 12V loads fit the ECI 20Ah LiFePO4 battery
  • You do not need AC power, or will add an inverter to the ECI kit
  • You can mount the ECI 40.2 x 20.1 in panel with the included brackets
  • You accept PWM rather than MPPT on the ECI 10A controller

The product at a glance

ECI Power 100W Solar Kit with LiFePO4

Best for: Sheds and small campers

Rated Power
100W
Panel Type
Monocrystalline Rigid
System Voltage
12V
Battery Chemistry
Lithium
Application
RV, Off-Grid, Marine
Features
Charge Controller

View on Amazon: ECI Power 100W Solar Kit with LiFePO4 Affiliate link

A complete small 12V kit: 100W mono panel, 12V 20Ah LiFePO4 battery (2,000 cycles at 80% DOD), 10A PWM controller with display, 12AWG cables and brackets. Light loads only; no inverter.

Pros

  • Fully matched kit
  • LiFePO4 battery included
  • 12AWG cables and brackets

Cons

  • Small 20Ah battery
  • PWM controller
  • No battery size or weight listed

Good fit if

  • You power a shed or coop with 12V lights and fans
  • You want the ECI kit to arrive ready to wire

Skip if

  • You run a 12V fridge overnight from the ECI 20Ah battery
  • You want MPPT and room to grow

Verdict: A complete, simple 12V starter kit sized for light loads.

Specifications side by side

Spec ECI Power 100W Solar Kit with LiFePO4
Rated Power 100W
Panel Type Monocrystalline Rigid
System Voltage 12V
Wattage 100W
Battery Chemistry Lithium
Application RV, Off-Grid, Marine
Features Charge Controller
Voltage 12V
Cell Type Monocrystalline
Dimensions 40.2 × 20.1 × 1.38 inches
Size 100W PWM
Model CLBE1220L100C6

Frequently asked questions

What comes in the ECI Power 100W 12V kit?

A 100W mono panel, a 12V 20Ah LiFePO4 battery, a 10A PWM controller, 10 ft MC4 cables, 6 ft battery cables and mounting brackets.

How many cycles is the ECI Power 20Ah battery rated for?

At least 2,000 cycles at 80% depth of discharge, and up to 5,000 at 50%.

Does the ECI Power 10A controller work on 24V?

ECI says it detects 12V and 24V systems automatically.

Does the ECI Power 100W kit include an inverter?

No, it is a 12V DC kit; AC loads need a separate inverter.

Can I add a second panel to the ECI Power 100W kit?

A second 100W panel would push the 10A PWM controller to its limit; plan a bigger controller if you expand.

See also