Lusperi 20 ft 14AWG 8mm (DC7909) Extension Cable Review
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
The Lusperi TS-187745-QW is a 20 ft extension cable with 8mm (DC7909) plugs, female on one end and male on the other, sold as a stand-in for Goal Zero's own 8mm 20-foot extension. It goes between a solar panel's 8mm lead and the 8mm solar input on a station, so the panel can sit in full sun while the Yeti stays in the shade, in a tent or inside the RV. The wire is 14AWG and the whole cable weighs 8.47 oz. Lusperi names only the Goal Zero Yeti 1250 for compatibility and gives no amp or voltage rating. We judged it from Lusperi's listing alone; it has not been plugged in here.
What stands out
- 20 ft of 14AWG cable
- 8mm (DC7909) female to male
- Sold as a replacement for Goal Zero's 20 ft extension
- Tool-free plug and unplug
- 30-day refund window
Who it fits
Good fit for
Goal Zero Yeti owners, or owners of other stations with an 8mm solar input, whose panel lead is too short to reach a sunny spot from where the station needs to sit.
Who should skip it
Stations with XT60, Anderson or MC4-only inputs, anyone who needs a published current rating before pushing high wattage through 20 ft, and anyone who only needs a few extra feet.
Verdict: A cheap, straightforward way to add 20 ft between an 8mm panel and an 8mm station; check the amp rating with Lusperi for big panels.
Lusperi 20 ft cable specs explained
20 ft length
Lets the station sit indoors or in shade while the panel follows the sun.
14AWG
Thick enough for typical portable panel currents over this distance; Lusperi does not give an amp limit.
8mm (DC7909) female to male
Plugs into the panel's 8mm lead on one end and the station's 8mm input on the other.
8.47 oz
Light; coils into a small bundle.
Only station Lusperi names: Yeti 1250
Other Yeti and 8mm-input stations should fit by plug type, but Lusperi does not list them.
What the cable is
It is a plain two-conductor 14AWG cord with molded 8mm (7909) plugs, called a 'High Power Port 8mm' on both ends in the listing. There is no inline fuse, switch or voltage reading. Lusperi sells a 30 ft version with the same plugs; the 20 ft length loses a little less voltage and is easier to coil. Lusperi offers a 30-day refund and promises replies within 24 hours.
Using a 20 ft 8mm extension
Connect the panel's 8mm lead to the cable's female end and push the male end into the station's 8mm solar input. Route it so it does not cross a walkway or get pinched in a door, and keep the joints off wet ground. Longer runs drop a little voltage, so if your panel is near the bottom of the station's input range, keep the run as short as you can. Unplug by the molded heads, not the wire.
Lusperi 20 ft fit check
Only plug type and current matter here.
Check before you buy
- Your station's solar input is 8mm (DC7909) for the Lusperi cable
- Your panel's lead ends in an 8mm plug for the Lusperi cable
- You need about 20 ft more reach from the Lusperi extension
- Lusperi confirms the cable's amp rating for your panel
- The Lusperi 30-day refund covers you if it does not fit
The product at a glance
Lusperi 20ft 14AWG DC 8mm Cable
Best for: Goal Zero Yeti solar setups
- Connector Type
- DC 8mm, DC 7909
- Compatible Devices
- Goal Zero Yeti 1250
- Cable Length
- 20 ft
- Wire Gauge
- 14AWG
- Dimensions
- 6.5 × 6.1 × 1.57 inches
- Weight
- 8.47 ounces
View on Amazon: Lusperi 20ft 14AWG DC 8mm Cable Affiliate link
A 20 ft, 14AWG extension with 8mm (DC7909) female and male plugs, sold as a replacement for Goal Zero's 8mm 20 ft extension and named for the Yeti 1250. 8.47 oz, no fuse or amp rating listed, 30-day refund.
Pros
- 20 ft reach
- 14AWG wire
- Matches Goal Zero 8mm ports
- Low cost
Cons
- No current rating
- Only one station named
- 8mm only
Good fit if
- You need the Lusperi cable between an 8mm panel and Yeti
- Your station must stay in shade 20 ft from the panel
Skip if
- Your station uses XT60 or Anderson, not the Lusperi 8mm plug
- You need a stated amp limit on the Lusperi cord
Verdict: A simple 8mm extension that does one job.
Specifications side by side
| Spec | Lusperi 20ft 14AWG DC 8mm Cable |
|---|---|
| Connector Type | DC 8mm, DC 7909 |
| Compatible Devices | Goal Zero Yeti 1250 |
| Cable Length | 20 ft |
| Wire Gauge | 14AWG |
| Dimensions | 6.5 × 6.1 × 1.57 inches |
| Weight | 8.47 ounces |
| Size | 20FT |
| Color | Black |
| Model | TS-187745-QW |
Frequently asked questions
Does the Lusperi 20 ft cable fit Goal Zero Yeti stations?
Lusperi names the Yeti 1250 and sells it as a replacement for Goal Zero's 8mm 20-foot extension; other 8mm-input Yetis should match by plug.
What wire gauge is the Lusperi 20 ft extension?
14AWG.
What plugs are on the Lusperi TS-187745-QW?
8mm (DC7909) female on one end and male on the other.
Can the Lusperi 20 ft cable connect MC4 panels?
Not by itself; you would need an MC4-to-8mm adapter first.
What is the Lusperi 20 ft cable's current rating?
The listing does not give one; ask Lusperi before running a large panel through it.
Featured in
See also
- grecell eb1000 999wh portable power station olive review
- duromax xp9500ih dual fuel inverter generator review
- duromax xp5500hx dual fuel generator review
- best generators under 100
- best generators under 150
- Best Generators Under $200 in 2026: 9 Picks Ranked by Specs
- Best Generators Under $300: 9 Spec-Based Picks
- 8 Best Generators Under $500, Compared
- rgeek 1106 DC to DC review
- shimano slx DC review
