As an Amazon Associate we earn from qualifying purchases. Affiliate disclosure

Renogy Side-of-Pole Solar Panel Mount RNG-MTS-SP100 Review

Latest update:

As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.

The Renogy RNG-MTS-SP100 is a side-of-pole mount: it clamps a single solar panel to a post or pole with two U-bolts, for sites where a roof is not an option. Renogy's title names its 50W panel and says it suits panels under 100W. The kit weighs 4.41 lb and the rails run 30.3 inches. It suits a small off-grid setup such as a gate opener, a trail camera battery or a 12V battery on a cabin post that tops up a power station. Renogy does not give a pole diameter range, a tilt range or a wind rating, so those are the questions to settle before you order. This review is based on Renogy's listing and spec fields; we have not installed it.

What stands out

  • Clamps one panel under 100W to a pole
  • Two U-bolts, two support arms, T-slotted brackets
  • Rails 30.3 inches long, kit 4.41 lb
  • End clamps for the panel frame

Who it fits

Good fit for

Owners of a 50W or 100W Renogy-size panel who want it on a post or pole above snow, brush or animals, away from a roof.

Who should skip it

Anyone mounting more than one panel, panels over 100W, or a flat RV roof, where a fold-down tilt mount is simpler.

Verdict: A practical pole mount for one small panel, as long as you confirm your pole size with Renogy first.

RNG-MTS-SP100 figures and what they mean

Panels under 100W (50W named)

Built for one small panel; a 200W module is outside its range.

2 U-bolts + 2 support arms

The arms set the tilt; the U-bolts grip the pole. No pole diameter is listed.

Rails 30.3 x 5.51 in

Long enough for the short side of a 50-100W panel's frame.

4.41 lb kit

Light enough to fit from a ladder with one helper.

4 end clamps

They grip the frame edge, so the panel does not need extra holes for the rails.

Tools not included

Socket wrench, torque extension, level, tape, 18mm and 13mm sockets.

Parts in the Renogy RNG-MTS-SP100 box

Renogy lists two T-slotted brackets, two L-channels, four L-brackets, two support arms, two U-bolts, eight T-bolts, ten cap head bolts, four end clamps and the matching nuts and washers (18 small spring washers, 18 small washers, four large washers, eight large nuts). The finish is silver. The spec fields give the rails as 30.3 inches long, 5.51 wide and 2.56 high. Renogy states no material, tilt angle or wind load, and there is no warranty term on the listing.

Putting a 50W panel on a post with the RNG-MTS-SP100

Fit the U-bolts around the pole, bolt the T-slotted brackets and L-channels into a frame, then clamp the panel's edges with the four end clamps. The support arms push the panel's lower edge out to set the tilt; Renogy gives no angle marks, so a phone level app helps. Once it is set, there is little to do: check the U-bolt nuts after the first storm and each season. If the panel charges a power station, run the MC4 lead down the pole and keep the station dry at the base.

Before ordering the Renogy RNG-MTS-SP100

Measure your pole and panel, then check these points.

Check before you buy

  • Your pole fits the RNG-MTS-SP100 U-bolts (Renogy gives no diameter)
  • Your panel is under 100W and its frame edge suits end clamps
  • You have 18mm and 13mm sockets for the RNG-MTS-SP100 nuts
  • You only need one panel on the pole, not an array

The product at a glance

Renogy Pole Mount for 50W Solar Panels

Best for: Single panel on a pole

Wattage
100W
Application
Off-Grid
Features
Solar Charging
Dimensions
30.3 × 5.51 × 2.56 inches
Weight
4.41 pounds

View on Amazon: Renogy Pole Mount for 50W Solar Panels Affiliate link

Renogy's RNG-MTS-SP100 side-of-pole mount holds one panel under 100W with two U-bolts, two support arms and four end clamps; the rails are 30.3 inches and the kit weighs 4.41 lb. Tools are not included, and Renogy lists no pole diameter, tilt range or wind rating.

Pros

  • Gets a small panel off the roof and onto a post
  • End clamps grip the frame edge
  • Full nut-and-bolt kit in the box

Cons

  • No pole size, tilt range or wind rating listed
  • Holds only one panel under 100W

Good fit if

  • You mount a 50-100W panel on a fence post or pole

Skip if

  • You plan a multi-panel array on one pole

Verdict: A tidy single-panel pole mount; confirm your pole size first.

Specifications side by side

Spec Renogy Pole Mount for 50W Solar Panels
Wattage 100W
Application Off-Grid
Features Solar Charging
Dimensions 30.3 × 5.51 × 2.56 inches
Weight 4.41 pounds
Size Pole Mount
Color Silver
Model RNG-MTS-SP100

Frequently asked questions

What panel size does the Renogy RNG-MTS-SP100 hold?

One panel under 100W; Renogy's title names its 50W panel.

Does the RNG-MTS-SP100 include a pole?

No. It is the mount only: brackets, rails, two U-bolts, end clamps and hardware.

What pole diameter fits the RNG-MTS-SP100 U-bolts?

Renogy's listing does not say; ask the seller before ordering.

What tools does the RNG-MTS-SP100 need?

A socket wrench with a torque extension, an 18mm and a 13mm socket, a level and a tape measure.

Can I tilt a panel on the RNG-MTS-SP100?

The two support arms set an angle off the pole, but Renogy lists no tilt range.

See also