As an Amazon Associate we earn from qualifying purchases. Affiliate disclosure

NURZVIY SolarFlex 100 Flexible Solar Panel Review: Who It Fits

Latest update:

As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.

The NURZVIY SolarFlex 100 is a 100W, 12V semi-flexible panel for curved or weight-limited roofs: van and trailer tops, boat decks, cabins and tents. Its main selling point is weight. At 4 lb and about 0.1 in thick, it is far lighter than a framed glass 100W panel, and it can be glued, taped or tied down where a rigid panel would need rails. NURZVIY uses monocrystalline back-contact cells under ETFE with a TPT backsheet. The listing is thin on electrical detail: no Voc, Isc or Vmp, no cable length, no connector type and no warranty. It also claims up to 50% higher conversion than ordinary panels, which reads as marketing rather than a measured figure. We wrote this from NURZVIY's published listing, not hands-on testing.

What stands out

  • 100W at 12V nominal
  • 4 lb and about 0.1 in thick
  • Monocrystalline back-contact cells
  • ETFE front, TPT backsheet
  • Bends to fit curved roofs and decks

Who it fits

Good fit for

Van, trailer and boat owners who want 100W on a curved or light roof and will run it through a 12V charge controller or a station's solar input.

Who should skip it

Buyers who need Voc and current figures before wiring, a stated warranty, or a panel that stays cool on a hot roof (flexible panels mounted flat run hotter than framed ones).

Verdict: A light 12V flexible panel for curved surfaces; check the label for Voc before you wire it.

SolarFlex 100 specs in plain terms

100W, 12V

Pairs with a 12V battery through a charge controller, or with a power station whose solar input accepts 12V-class panels.

4 lb, about 0.1 in thick

Light enough for a pop-top, kayak rack or canvas roof that cannot carry glass.

Back-contact mono cells

No busbars on the front face; NURZVIY's 50% efficiency claim has no stated basis.

ETFE surface, TPT backsheet

ETFE resists UV and yellowing better than PET; the TPT layer helps with heat and moisture.

Size field 30 x 50 x 2 in

Likely the box; the same figures appear on NURZVIY's 400W listing, so measure your roof before ordering.

Semi-flexible build

The SolarFlex 100 has no frame or glass. The cells sit between an ETFE front and a TPT back layer, which is why it bends and weighs so little. Flexible panels shed heat poorly when stuck directly to a roof, so leave an air gap or accept some loss on hot days. NURZVIY says it handles high wind and snow loads but gives no Pa ratings, and the listing names no IP rating, mounting holes, cable or plug.

Mounting and charging with the NURZVIY 100W

On an RV or boat, fix the panel with adhesive, screws through grommets if present, or straps, then run its leads to a 12V PWM or MPPT controller. For a power station, add an MC4-to-XT60 or Anderson adapter if the leads end in MC4 (the listing does not say). Choose the SolarFlex 100 if roof weight and curve are the limits; choose a rigid 100W panel if you have a flat roof and want better heat tolerance and fuller specs.

Before buying the NURZVIY SolarFlex 100

Confirm the electrical fit and the mounting plan.

Check before you buy

  • Your controller or station solar input accepts a 12V NURZVIY SolarFlex 100
  • You will check the SolarFlex 100 label for Voc and Isc on arrival
  • You have an MC4 or adapter plan, since NURZVIY lists no connector
  • Your roof leaves a little air gap behind the NURZVIY panel

The product at a glance

NURZVIY 100W Flexible Solar Panel

Best for: Curved RV and boat roofs

Rated Power
100W
Panel Type
Flexible
Cell Type
Monocrystalline
System Voltage
12V
Weight
4 lbs
Application
RV, Off-Grid, Car, Marine

View on Amazon: NURZVIY 100W Flexible Solar Panel Affiliate link

A 100W, 12V semi-flexible panel with back-contact mono cells, an ETFE face and TPT backsheet. About 4 lb and 0.1 in thick, it suits curved van, trailer and boat roofs. The listing gives no Voc, Isc, connector, cable length, IP rating or warranty.

Pros

  • 4 lb for 100W
  • Bends to curved roofs
  • ETFE surface

Cons

  • No Voc or Isc listed
  • Connector not named
  • No warranty stated

Good fit if

  • Your roof is curved or weight-limited
  • You run a 12V controller

Skip if

  • You want full SolarFlex 100 electrical specs first
  • You have a flat roof for a framed 100W panel

Verdict: A light 12V flexible panel with sparse electrical specs.

Specifications side by side

Spec NURZVIY 100W Flexible Solar Panel
Rated Power 100W
Panel Type Flexible
Cell Type Monocrystalline
System Voltage 12V
Weight 4 lbs
Wattage 100W
Application RV, Off-Grid, Car, Marine
Voltage 12V
Dimensions 30 × 2 × 50 inches
Color 100W
Model SolarFlex 100

Frequently asked questions

How much does the NURZVIY SolarFlex 100 weigh?

About 4 lb, at roughly 0.1 inches thick.

What voltage is the NURZVIY SolarFlex 100?

It is sold as a 12V, 100W panel; Voc and Isc are not given in the listing.

What cells does the NURZVIY SolarFlex 100 use?

Monocrystalline back-contact cells under an ETFE surface with a TPT backsheet.

Does the NURZVIY SolarFlex 100 include cables or a controller?

The listing does not mention any cable, connector or controller.

How big is the NURZVIY SolarFlex 100?

The size field reads 30 x 50 x 2 inches, which looks like packaging; confirm panel dimensions with the seller.

See also